Hardware

Barnfold Door Hardware Installation Instructions for ONE Folding Door

Barnfold  Hardware Kit—  Installation instructions for the patent pending BARNFOLD  hardware system.

Installation Instructions For the Following Osborne Barnfold Hardware Part numbers:  4941.64 4941.52 4941.40 4941.28

OVERVIEW

The Barnfold  hardware system provides the movement of our barn doors with the convenience of a track which does not extend beyond the width of the opening. We suggest measuring your opening from outside of the casing, which allows the doors to completely cover your opening. If there is no trim, add 1” to the width and ½” to the height measurement. With this overall dimension, determine if you want 2 or 4 doors. 

All doors using the barnfold  system must be hinged to create a bi-fold door. (We recommend using piano hinges.) You will need to mount one stationary hanger on one side of the doors, and one articulating hanger on the other side of the bi-fold doors. On the bottom of the doors, your bracket is mounted to be used with the pivot hinge.

The track is located above the opening, mounted and the barnfold system is complete. All hardware components are included with your BARNFOLD  hardware kit. All track mounting hardware is included with the track kit. We recommend installing the track, and stationary hangers on a ledger board over the head casing, to ensure a strong attachment to the wall.

STEP 1: INSTALL THE HINGES BETWEEN DOORS

Place doors face down and square top edge. Allow 1/8”space between doors and secure hinge mechanism.

STEP 2: INSTALL BOTTOM BRACKET ON OUTSIDE CORNER.

The bottom bracket has two 1/8” holes and one 5/16” hole. Place bracket on bottom outside corner with 5/16” hole located 1”  from outside edge of door and centered on bottom rail. Install ¾” screws and drill through the 1/4” hole 1/2” into the door stile.

STEP 3: INSTALL BARNFOLD  STATIONARY HANGER

The stationary hanger is installed on the top edge of the door with the bottom bracket. Place the hanger on the face of the door, with the holes 1-1/4“ from the outside edge. Allow a small space between the pivot and the top of the top of the door (1/16” recommended), and mark the 2 bolt holes. Drill 3/8” holes through the door where marked, and install anchors from the back side of door. Use small washer and bolt the hanger in place.

  Barnfold  Stationary Hanger    

((Stationary Hanger with Lag bolt through wheel to ledger board)     

STEP 4: INSTALL BARNFOLD  ARTICULATING HANGER

On the opposite top door edge, install the articulating hanger. Place the hanger on the face of the door, with the holes 1-1/4” from the outside edge. Allow a small space between the pivot and the top of the door (1/16” recommended), and mark the 2 bolt holes. Drill 3/8” holes through the door where marked, and install anchors from the back side of the door. Use small washer and bolt the hanger in place.

Barnfold  Articulating Hanger

(Pivot Hanger that rolls, and steps off track.)

This image has an empty alt attribute; its file name is a0OzJe4uLLRA4evksmt8SFIKZTZIdwOSBeyxsoKrTI4DvpOEiQ1vWbQ_bfJuMGiya4yCkoySCg1xwFAK3Forc0-bwSCU29Hac1nv0B-DjJ740cXRnDLR4xAaRVSfqJlxeU8FQa9dFcA1QWx_3A

STEP 5: LOCATE ASSEMBLED DOORS IN OPENING AND INSTALL PIVOT BRACKET

Center assembled doors in the opening and mark the outside bottom corners. Depending on the operation of the doors, install the outside edge of  the “L” bracket ½” in from the mark, flush with the wall. If using the straight pivot bracket, install outside edge ½”from the mark, and the pivot 1-5/8” from the front edge of the opening. Carefully install pivot bracket in this position with ¾” screws.( typically for floor mounting )

    (Pivot Bracket)

STEP 6: INSTALL TRACK

Place assembled doors on the pivot bracket and mark the top edge of the door on the wall. Measure up 2-1/4” and make a mark—this will be the top edge of the track. Locate your track on this mark, level your track, and mark the end holes. Drill 1/8” holes and lag track to the wall or ledger board. Drill and fasten the remaining lags.  Use the 1- 3/8” spacer on the back of the track, and a flat washer on the front.

STEP 7: INSTALL DOORS IN OPENING

Place barnfold  assembly on pivot, with the stepped roller on the track. Center stationary hanger and mark the hole location through the wheel on the wall. Drill a 1/8” guide hole at this location. Using a flat washer, 5/16” x 4” lag bolt, ½” spacer, stationary hanger, and 1-1/4” spacer lag  the assembly in place. Do not tighten at this time. Check that the movement of the barnfold  system allows you to close and fully open, then tighten all fasteners. 

CONGRATULATIONS ON INSTALLING YOUR NEW BARNFOLD HARDWARE

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: