Gallery, Posts, Legs and Table Skirts

Island and Table Leg Services

Island and Table Leg Service
Island and Table Leg Service
Island and Table Leg Service

At Osborne Wood Products, all Standard Island and Table Legs will come unfinished and without any cuts or hardware. In order to make your project easier, Osborne offers services specifically for Kitchen Island Legs and Table Legs that can be added to your order.

Please note that all orders with any of the following services added will be considered ‘Custom‘ and are not eligible for return.

You will need to order your products with these services through our Customer Service Department by calling 1-800-849-8876. Services cannot be done online.

Services for Island and Table Legs:

Sanding, Millwork and More:

Sanding to 220 Grit– Our products are sanded to 150 grit as a standard. If you need your items sanded to 220 grit, we can do that for you as well. This additional sanding can only be done on Turnings made In House. Please check with our customer service representatives to make sure your items are eligible for this service. There is a $8.00 per item service charge on 220 Grit Sanding.

No Sanding– We can ship an item without any sanding. The item must be manufactured In House. There is no additional charge for this service. Please check with our customer service representatives to make sure your items are eligible for this service.

Hand Select– We can hand select from in stock items for specific traits. An example of this would be hand selecting a knotty pine leg for the greatest number of knots, or hand selecting a soft maple leg for the least amount of color variation.  There is a $5.00 fee per item for this service. This service only applies to items that are currently in stock. Please check with our customer service representatives to make sure your items are eligible for this service.

Hand Select from Raw Material – On items made in house that are not in stock we can hand select the raw lumber for specific traits.  An example of this would be hand selecting a knotty pine leg for the greatest number of knots, or hand selecting a soft maple leg for the least amount of color variation.  There is a $10.00 fee per item for this service. This service only applies to items that are currently out of stock and are made In House. Please check with our customer service representatives to make sure your items are eligible for this service.

Solid Stock Only– You may request that only solids be sent for an item when they are available in stock.  Items over 3.5″ wide are almost impossible to get as solids, as they tend to crack easily.  Some wood types it is hard to get in solids under 3.5″ wide as well, so if it is not in stock our customer service representatives may need to check with production before putting this service in.  The fee for this is $5.00 per item.

Exterior Glue– Although we do not recommend our products for exterior use you may request exterior glue be used in the production of your products. The items must be manufactured In House. There is a $6.00 per item service charge for using exterior glue. Please check with our customer service representatives to make sure your items are eligible for this service.

Quarters– A turning may be sent as quarters (all four quarters sent). The item must be symmetrical in order for the product to be eligible for this service. Note: Quarters does allow for the width of the saw blade and are not “Perfect Quarters.”  The fee for this is the price of the leg before discounts.

Quarter Notch– 1/4 of the leg will be removed, and both sections will be sent with order.  The fee for this service is 50% of the price of the leg before discounts.

Rectangular Split– The leg will be cut in half for you, from top to bottom.  Both halves are shipped with your order.  The fee for this service is 50% of the price of the leg before discounts.

Diagonal Split– Split leg diagonally.  Both pieces are shipped with order.  The fee for this service is 50% of the price of the leg before discounts.

Trim Leg– If you have a specific leg style in mind but need it a little shorter, we can make this happen without a custom! Trimming is $7.50 per cut per leg. Cuts can be made at the top and/or bottom of the turning.

Chamfer– Our chamfer service is done to the top square of the leg. The width and height of the chamfer must be specified. Our standard chamfer is ¾” wide and 4” tall. This service can be added to a leg if the top square will accommodate the specified dimensions, and it is $2.00 per leg.

Skirt Legs– If you order a skirt set, this service will be done automatically and is included as part of the cost of the skirt kit. This service will mill the legs with mortises to match the tenons on the skirt boards, chamfer the corner, and add a threaded insert to go with the hardware for the corner braces. You can check out our table base creation page on our website: https://www.osbornewood.com/table_base_kits.aspx

Receptacle Notch– Our receptacle notch service is the following size: Receptacle notch is cut 1 ¼” from the top, 3” long, 2” wide, and 2 ¼” deep. There will be a 1″ hole through the center of the leg, so the leg must be at least 1 ¾” wide the entire length.  The item must have a top square in order to be eligible for this service, as the notch will be centered in square, and the top block must be at least 5″ tall and 3″ wide. Specifications other than these listed may be done as custom millwork. Contact customer service for availability of other options. The price of our standard receptacle notch is $49.99.

Shelf Notch– A shelf notch can be added to a square block on the bottom of one of our products. The notch will meet your specification of distance from floor and thickness of the notch, so a CAD drawing will need to be created and approved. Service charge is $35.00 per notch. The leg must have a bottom or middle square.

Mortise– Legs can be mortised on the top or bottom square of the product. The mortise may be milled into 1,2,3 or 4 sides of the leg (if 2- opposite or adjacent). Our standard mortise is 3” long x 3/8” wide x 7/8” deep and is set about 5/8” from the top of the leg. Items must have a top or bottom square in order to accept the mortise. A $10.00 service charge per leg will apply.

Through Hole– Items manufactured In House may have a 1″ hole through the center of the product. The leg must be at least 1.75″ for the entire length, and 2″ is ideal. This service is $35.00 per leg.

Custom Milling– Do you have a milling need not mentioned in this section? Contact our friendly customer service representatives for a quote to meet your milling needs. 1-800-849-8876

Installation:

Install Bolt/Screw in Chamfer– Hardware may also be installed in a chamfer. Our chamfer service is done to the top square of the leg. The width and height of the chamfer must be specified. Our standard chamfer is ¾” wide and 4” tall. Then, the hardware of your choice will be installed at a designated height in the chamfer. A distance from the top of the leg to the center of the bolt/screw must be specified. The hardware must be added to the order so that it may be installed in the leg. This service charge is $5.00 per item. 

Custom Install Hardware– Can’t find the installation you need for your product? Request a custom install with our friendly customer service staff at 1-800-849-8876. Prices will vary depending on service.

Island and Table Leg Service

Please feel free to take full advantage of the services listed above! Our customer service representatives are standing by, and will assist you in determining exactly what you need in order to successfully complete your project.

If there is a custom service required, but it is not included on this list, please call us! We would love to check the available options for you in order to help meet your woodworking needs.Our friendly staff is on the line from 8am to 7pm EST ready to assist you. Please call 1-800-849-8876 to speak with a representative today.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: